The system includes accessories such as prefabricated corners, sealing tapes, collars, butyl strips and thus covers all areas of application.
For easy handling, the waterproofing membrane is 500 mm wide and offers a 50 mm wide stripe, free of non-woven, for secure overlapping of the waterproofing surface.
The Peel & Stick Sealing System is perfectly suited for waterproofing in bathroom areas due to its simple and quick installation. The uncomplicated application enables easy sealing of the application areas.
- Approved waterproofing sealing system
- Complete system solution with all necessary waterproofing elements
- No need to use extra adhesives on the substrate
- No drying time
- Quick and easy installation of the components
- Immediately ready for tiling after installation
- Tiles are easier to lay due to the extremely thin overlap area
Significant time saving during installation compared to conventional waterproofing
The System
The Peel & Stick Sealing System is a practical solution for an easy and quick to apply sealing system for bathrooms and internal wet rooms. No additional adhesive is required for the installation of this sealing system. Due to the butyl coating on the back side, the components can be easily applied to the substrate by peeling off the release paper. With the non-woven front-side coating of the membrane, tiling can be started directly after the waterproofing is installed.
Components
Sealing membrane
Sealing tape
Outside Corner
Inside Corner
Butyl stripe
Closure tape/Base tape
Upstand tape
Waterpipe collar
Floor drain collar
Tape for application to linear drainages
Installation
Quick and easy
Before laying the membranes and system components, the substrate should be even, smooth and free of adhesion-reducing components. If necessary, use a primer to bind dust.
First install the accessories of the waterproofing system such as corners, waterpipe collars, butyl stripes or upstand tape.
Cover the overlapping areas with the butyl adhesive strip. Remove the release film and press the entire surface forcefully and over the entire surface using a pressure roller.
In accordance with DIN 18534, the waterproofing membrane should overlap the system components by at least 5 cm. When laying the membranes and accessories, ensure that they are installed without folds or bubbles.
You can now start tiling without any drying time.
Application video
Questions & answers
Why was the Peel & Stick system developed?
The Peel & Stick system was developed to meet the increasing demands for simple, quick and clean waterproofing systems for everyone.
What are the advantages of the Peel & Stick system?
- Simple, safe, and clean application
- No special tools and set-up times necessary
- Decreased application time and cost savings during application
- Tiling without drying time directly after application
- Decoupling and Sealing membrane all in one
For which target groups is the Peel & Stick system particularly suitable?
The Peel & Stick system is an innovative and perfect solution for tilers, the entire sanitary industry, and producers in the construction industry. In addition, the Peel & Stick system is particularly interesting in the prefab and system construction sector. Due to the easy application, the Peel & Stick system is also highly attractive for the DIY sector.
How does the application work?
- Prepare substrate
- Apply the system components
- Seal overlapping areas of the corner with butyl adhesive tape
- Apply sealing membrane
What are the possible purchase motives of customers or end customers/processors?
Customers can supplement their product range with the self-adhesive waterproofing system.
The Peel & Stick system enables new entry into the waterproofing industry.
What are possible objections and questions from customers or end customers/processors?
What tests does the system have?
An abP is in the final phase.
Who is responsible for installing the system?
The Peel & Stick system is installed by tilers as usual, but the system is also suitable for DIY. This opens up new customer groups (plumbers, sanitary customers) or sales approaches.
Outside of strictly regulated markets, anyone with manual skills can apply the system.
Is the system chemically resistant?
Yes, against aqueous acids and alkalis.
Is the material resistant to ageing?
Yes.
Is the material repairable?
Yes.
Does the butyl lamination adhere to all common building substrates?
Yes, as long as the underground is clean, dry, smooth, and load bearing – primer is recommended.
Which tile adhesives is the PP non-woven suitable for?
The PP non-woven enables a good bond with the usual tile adhesives and sealants.
For which area of application is the system suitable?
The Peel & Stick system is suitable for bathrooms and wet rooms indoors in combination with tiles. This applies to water exposure classes W0-W2.
What system parts and kits are available?
Ready-to-use kits can be assembled according to customer requirements (DIY, sanitary industry, etc.). All system parts are also available individually (note minimum order quantity if necessary).
What is the max. width and roll length for the self-adhesive sealing membrane for industrial customers?
Max. Width is 1000 mm with a max. roll length of 250 m. Special dimensions are possible by arrangement.
All common possibilities (printing, scaling, packaging, label etc.), as well as coloured butyl in red, blue, yellow and grey can be realised.
All common possibilities (printing, scaling, packaging, label etc.), as well as coloured butyl in red, blue, yellow and grey can be realised.
